A starting point for your project

Cement products / brick shed design 18 × 36 m starting form

Coordinate material preparation, production envelopes and finished-product staging inside an enclosed starting shell. Use the model to discuss movement and working zones before detailing the plant and civil works.

Open this concept in 3D Explore quantities

Furnished cement products / brick shed 3D concept showing the frame and illustrative interior equipment — Illustrative preset preview. Current starting inputs are listed below; inspect changes in the live editor.

Floor footprint: 648 m²18 × 36 m width × length
Eave height: 4.5 mCheck actual underside clearance
Bays along the length: 6 bays6.00 m centre-to-centre
Wall arrangement: Open sides · no wall claddingStructural members remain at openings

Same footprint. Three bay arrangements.

See what changes the steel quantity.

The range compares 5, 6, 7 bays at the same width, length, eave, roof, openings and selected sections. It describes those modelled arrangements; it is not an engineered minimum–maximum allowance.

23.9–27.7kg/m² of floor footprint

2.22–2.57kg/sq ft of floor footprint

Concept take-off, sections not designed — run the section sizing screen

Starting 6-bay model: 16,709 kg of modelled steel.

See exact scenarios and quantity basis

Bays	Bay spacing (m)	Model steel (kg)	kg/m²	kg/sq ft
5	7.20	15,494	23.91	2.221
6starting	6.00	16,709	25.79	2.396
7	5.14	17,957	27.71	2.574

Primary / secondary / brace sections: BSP MB 300 × 140 · MC 100 × 50 · ISA 75 × 75 × 6

End-wall framing is enabled, matching a fresh editor preset; modelled end posts are included where walls are clad. This is net frame, secondary-member and plate mass. Procurement waste, cladding, civil works, furnishings and equipment loads remain separate. No price, safe capacity or design approval is inferred.

More than an empty shell

A furnished starting layout.

The current fit-out generator places 16 physical objects in this starting model. These counts come from that generated layout.

1
Feed / grain hopperRaw material hopper
1
Process tankMixer envelope
1
Processing machineBlock / brick press envelope
1
ConveyorPallet transfer conveyor
5
Palletised goodsCuring pallet
1
Workshop benchQuality check bench
4
Linear light fixtureGeneral light
2
Extinguisher positionFire equipment position (review required)

The 3.0 m central stripe is a planning reserve, not an approved exit route or vehicle swept-path result. Equipment is generic; confirm capacity, service clearances and actual loads separately.

Before you build your brief

Questions, answered.

A closer look at the cement products / brick shed concept, its editable inputs and the decisions that belong in a project-specific design.

What are the starting dimensions of the cement products / brick shed?

The preset starts at 18 m wide by 36 m long, with a 4.5 m eave and 6 bays along its length. You can edit these dimensions. They describe a concept starting form, not an operating capacity or approved structural design.

Does the cement-products model define a production rate?

No output capacity follows from the generic machine and storage objects. Establish the intended products, moulds, handling method and actual plant layout with the equipment supplier.

Are vibration and machine foundations designed?

The preset does not calculate dynamic actions or machine bases. Obtain supplier reactions, operating frequencies and anchorage requirements for the civil and structural design.

Where should curing and finished-product storage go?

Use the site and equipment brief to reserve the required indoor or outdoor areas. Curing process, duration, moisture management and stacking loads are not determined by the shed model.

Does the model include dust control and wash-water treatment?

No process extraction or water-treatment system is sized. Coordinate dust collection, cleaning, drainage and material handling with the actual plant and site requirements.

Explore another starting point

View all 20 concepts